pump – AKT Motor and Drive

DSL806 Low Voltage Brushless DC Servo Drive

admin — Wed, 27 Oct 2021 18:53:34 +0000

Safety Precautions Please read carefully before using in order to avoid the damage of the drive

Open box to check

If found any parts missing or found drives damaged, do not install them.
The servo drive must be used with a matching servo motor.

Installation

Installed on a non-flammable metal frame to prevent intrusion of dust, corrosive gases, conductive objects, liquids and flammable materials, and maintain good heat dissipation conditions;
When installing, be sure to tighten the mounting screws of the drive. The servo drive and servo motor should be protected from vibration and must not be subjected to impact.

Wiring

Please perform the wiring work by professional electrical engineers;
Before wiring, please confirm that the input power is in the off state. Wiring and inspection must be performed after the power is cut off and the drive indicator is off to prevent electric shock;
When plugging and unplugging the terminal of the drive, please make sure that the drive indicator is off;
The grounding terminal PE must be reliably grounded through the left side of the drive;

Please set the emergency stop circuit outside the controller;
Do not connect the power input cable to the output U, V, W terminals;
Tighten the output terminals with a suitable torque.

Power on

Please confirm whether the main circuit input power supply and the rated working voltage of the drive are consistent; Do not test the drive for high voltage and insulation performance;
Do not connect the electromagnetic contactor or electromagnetic switch to the output circuit.

General

DSL806 low voltage direct current servo drive is developed by high-performance processor, which provides users with a cost-effective servo control.

The solution is to ensure the stability and reliability of the system and to meet the most common application functions and performance.
Compared with stepping products, the servo drive has the advantage of low noise, low heating, high speed, constant torque output, no loss of step.
Compared with stepping servo products, this servo drive completely abandoned the inherent disadvantages of stepping products. Function, performance and reliability are better.
Compared with worldwide well known high-voltage servo, this drive has the similar performance with cheaper price and easy to use.

I. Basic Characteristics

Working voltage: 18V-60VDC;
Output current: rated 8A, peak 24A;
Rated speed: 3000RPM, supporting the highest 10000RPM;
Compatible motor: 5W-600W low voltage servo motor, DC brushless motor with encoder or hollow cup motor.
Control mode: external pulse, analog, RS232 communication control. For position, speed and torque mode;
Parameter adjustment: RS232 communication, PC debugging software written, or handheld debugger.
Abnormal protection: with under-voltage, over-voltage, overload, over-current, encoder abnormal functions. Alarm output function inside.

II. Applicable fields

All kinds of electronic processing equipment, production line transmission equipment, medical equipment, instruments and meters, precision testing equipment, channel or gate control, AGV/RGV, Cartesian robot, servo length positioning, garage block control, and equipment, Feeding equipment, auxiliary motion equipment, grabbing and handling machinery, jet printers, photo machines, households and office automation devices.

III. Technical indicators

Using FOC field oriented control technology and SVPWM space vector modulation algorithm. The parameters for the motor can be easily modified to fit various specifications of the motor, built-in electronic gear, graphical debugging and monitoring software. Customization is available according to the user’s functional required. Simple control functions can be integrated.

Repeat tracking error: ±1pulse;
Speed control accuracy: ±1RPM;
Receiving frequency range: 1MHZ;
Maximum speed support: 10000RPM;
Minimum speed support: 1RPM;
Positioning accuracy support: 1/10000;
Maximum no-load acceleration: 200RPM/ms;
Suitable motor: 24V/36V/48V/60V low voltage servo motor, brushless DC motor with encoder or hollow Cup motor.

IV. Interface identification

4.1 Power Motor Connector CN1

Item	Mark	Description	Note
1	VDC	Input Power +	DC 18V-60V
2	GND	Input Power –	DC 18V-60V
3	U	U phase	Must be connected to the motor as indicated
4	V	V phase
5	W	W phase

Figure 4-1

4.2 Encoder Connector CN2

Item	Mark	Description	Item	Mark	Note
1	GND	Output Power Ground	7	B+	Encoder B phase positive input
2	VCC	Output Power +5V	8	A+	Encoder A phase positive input
3	W+	Encoder W phase positive input	13	Z-	Encoder Z phase negative input
4	V+	Encoder V phase positive input	14	B-	Encoder B phase negative input
5	U+	Encoder U phase positive input	15	A-	Encoder A phase negative input
6	Z+	Encoder Z phase positive input

Figure 4-2

4.3 Control Connector CN3

Item	Mark	Description	Note
1	PUL+	Phase positive input	Pulse signal: pulse rising edge is effective. 4-5v at high level, 0-0.5v at low level, Pulse width should be greater than 1.6us, If you use 12V or 24V, you must connect 1.5-2.2K resistors in series.
2	PUL-	Phase negative input
3	DIR+	Direction positive input	Direction signal: input between DIR+ and DIR- Reverse at high level, and vice versa. The direction signal should be established at least 5us before the pulse signal. 4-5V at high level and 0-0.5V at low level. If you use 12V or 24V, you must connect 1.5-2.2K resistors in series.
4	DIR-	Direction negative input
5	ENA+	Enable positive input	Enable signal: This signal is used to enable or disable the servo motor. When the high level between ENA+ and ENA-, the drive will cut off the motor power, leaving the motor in a free state and not responding to the pulse. Enable the motor when the low level between ENA+ and ENA-, If you use 12V or 24V, you must connect 1.5-2.2K resistors in series.
6	ENA-	Enable negative input

Figure 4-3

4.4 Communication Interface CN4

Terminals No.	Description	Note
2	RXD	Connect to Computer serial port TXD
5	TXD	Connect to Computer serial port RXD
6	+5V	Drive external +5V output, maximum 100mA
3	GND	Signal ground

Figure 4-4

4.5 Expansion interface CN5

Item	Mark	Description	Note
1	VCC	Output power +5V	Drive external +5V output, maximum 100mA
2	GND	Output power ground
3	A+	Differential output A+	Encoder feedback output, consistent with the encoder input line number
4	A-	Differential output A-
5	B+	Differential output B+
6	B-	Differential output B-
7	Z+	Differential output Z+
8	Z-	Differential output Z-
9	AI	Analog input	0-5V，0-2.5 REV，2.5-5V FWD
10	GND	Output power ground
11	Fault	Open set alarm output	Above 5V, it needs to be connected in series with 2K resistors.
12	COM	Open set output common port	Connect controller common port

Figure 4-5

V: Control Mode

5.1 Basic control

This drive provides three basic operating modes: position, speed and torque. Using a single control mode, all operating modes and instructions are listed below.

Control mode selection	Control source selection	Note
Position control mode	External pulse input	The drive accepts a position command to control the motor to the target position. The position command is input by the terminal, and the signal type is pulse + direction
	PC digital input	Relative position: The drive enable start time is mechanical zero point, each time the PC digital value inputted, the motor rotates the target distance. Absolute position: The drive enable start time is mechanical zero point, each time the PC digital value inputted, the motor is referenced to the mechanical zero point and is rotated to the target position.
	External analog input	When the external analog input is 0~+5V, the motor rotates in absolute position mode -16384~+16384 pulses
Speed control mode	PC digital input	Input range：-10000RPM~+10000RPM
Speed control mode	External analog input	When the external analog input is 0~+5V, the motor runs at -12000RPM~+12000RPM.
Torque control mode	PC digital input	The input range is -7500~+7500. The corresponding output current is 24A. When the input is positive va;ie, it corresponds to the positive torque, the negative value corresponds to the reverse torque.
Torque control mode	External analog input	When the external analog input is 0~+5V, the corresponding digital torque range is: -16384~+16384. Drive internal limit to a maximum of 7500

Figure 5-1

5.2 Communication Control

In addition to the basic control methods described above, the drive also provides RS232 communication control. When selecting the communication control mode, whether you select any of the control modes, the control source must select the PC digital input, then transmit data according to the communication format and drive. The following are some specific instructions for communication control.

Function	Data address(A1)	Data up 8 bits (A2)	Data low 8 bits (A3)	Data checksum (A1+A2+A3)		Note
Motor start	0x00	0x00	0x01	0x01		Write motor enable
Motor stop	0x00	0x00	0x00	0x00		Write motor disable
Speed mode selection —PC digital input	0x02	0x00	0xc4	0xc6		Control mode given command source selection
Position mode selection — External pulse input	0x02	0x00	0xc0	0xc2		Control mode given command source selection
Position mode selection –PC digital input	0x02	0x00	0xd0	0xd2		Control mode given command source selection
Speed proportional gain	0x40			Take low 8 bits (A1+A2+A3)		It is recommended to make the changes based on the factory default parameters according to the actual situation.
Speed integral gain	0x41			Take low 8 bits (A1+A2+A3)
Speed differential gain	0x42			Take low 8 bits (A1+A2+A3)
Position proportional gain	0x1a			Take low 8 bits (A1+A2+A3)
Position differential gain	0x1b			Take low 8 bits (A1+A2+A3)
Position feed forward gain	0x1c			Take low 8 bits (A1+A2+A3)
Speed mode (available when PC digital input)– acceleration and deceleration speed setting	0x0a	acceleration	deceleration	Take low 8 bits (A1+A2+A3)	Actual speed=( acceleration and deceleration speed/250)*6000
	0x0a			Take low 8 bits (A1+A2+A3)
Speed mode –PC digital input — speed given	0x06			Take low 8 bits (A1+A2+A3)	Set digital 16384 corresponding to the actual speed 6000RPM
Position debugging mode The position is given a up 16 bit –PC– position	0x50			Take low 8 bits (A1+A2+A3)	Up 16 bits of the 32-bit data input
Position debugging mode The position is given a low 16 bit –PC– position	0x05			Take low 8 bits (A1+A2+A3)	Low 16 bits of 32-bit data input
Find Z signal, mechanical origin	0x53	0x00	0x00	0x53
Absolute position/relative position switch control in position mode	0x52	0x00	0x00	0x52	Absolute position
	0x52	0x00	0x01	0x53	Relative position
Speed limit value in position mode (The actual speed at the given position under the position command)	0x1d			Take low 8 bits (A1+A2+A3)	Set digital 16384 corresponding to the actual speed 6000RPM
Speed limit value in position mode: In the position mode PC input acceleration/deceleration setting parameter, “Acceleration/Deceleration” set to maximum will be the leading role, otherwise it will affect the final speed limit value. For example, in the host computer debugging software, input “Acceleration: 255 / Deceleration: 255” in the position mode PC input acceleration/deceleration setting, then submit the input. After the input is completed, the final speed value for the limit is the value assigned to the address of register 0x1d.

Read monitoring parameters	Sending 0x80 0x00 0x80 directly, drive will return the corresponding monitoring information
Failure state	0x80	0x00	Status_word	Take low 8 bits (A1+A2+A3)	Status_word is customized parameters
	The fault information corresponding to each bit of Status_word is as follows (highly effective) : Status_ov_i = Status_word^1; over current Status_ov_u = Status_word^2; over voltage Status_err_enc = Status_word^3; encoder error Status_ov_q = Status_word^5; under voltage Status_ov_load = Status_word^6; over load
Busbar voltage	0xe1			Take low 8 bit (A1+A2+A3)	(Deviation 2V)
Output current	0xe2			Take low 8 bit (A1+A2+A3)	The actual current will reduced by 100 times
Output speed	0xe4			Take low 8 bit (A1+A2+A3)	Returned digital 16384 corresponding to the actual speed 6000RPM
Position give up 16 bits	0xe6			Take low 8 bit (A1+A2+A3)	If the position is given as 32-bit data, the actual value is recombined according to the up 16 bits and the low 16 bits.
Position give low 16 bits	0xe7			Take low 8 bit (A1+A2+A3)
Position feedback up 16 bits	0xe8			Take low 8 bit (A1+A2+A3)	If the position feedback is 32-bit data, the actual value is recombined according to the up 16 bits and the low 16 bits.
Position feedback low 16 bits	0xe9			Take low 8 bit (A1+A2+A3)

Figure 5-2

Detailed description of the communication control instructions:

(1) The data command format received by the controller is: address + data up 8 bits + data low 8 bits + data checksum
(take the low 8 bits value of the summary of first three data) If the host computer sends correctly in this format, the drive will immediately return the two addresses of the command to the host computer, which indicates that the drive has successfully received the command. For example: the host computer sends: 0x09 0x32 0x32 0x6d, the drive returns to the host: 0x09 0x09, at this point, it means the drive has been finished receiving. (Note: There must be more than 1ms delay between each data instruction, otherwise the data is prone to error).

(2) When the position debug mode is selected and the host machine sends the control command through the serial port, the setting sequence is: set the drive to position debugging mode (send 0x02 0x00 0xd0 0xd2)  set the speed limit value in position mode  motor start (0x00 0x00 0x01 0x01)  position given up 16 bits  The position is given by the low 16 bits. If the position debug mode has been determined and the motor has been started, it will not need to be sent repeatedly when it is sent next time.

(3) If all parameters have been set when the drive is debugging parameters, such as acceleration and deceleration, control mode, speed limit (the factory has set a suitable value). At this time, it is only necessary to set the motor to start, and then send the position. Step: Motor start (0x00 0x00 0x01 0x01) position is given up 16 bits position is given low 16 bits.

(4) The input length given by the position is a 32-bit data, which must be decomposed to a up 16 bits and a low 16 bits when transmitted.
Moreover, the 16-bit data is also need to be decomposed into up 8 bits and low 8 bits. The data splitting will be done by the data format generator in the file. The user only needs to input the data to be sent, it can be automatically split into the format used for communication.

(5) Use of the data format generator. For example, set the acceleration and deceleration to 50 and place it in the 16-bit data generation box: Address: 09 Acceleration input 50, Deceleration input 50 then display. At this time, the data format is generated 0x09 0x32 0x32 0x6d and then the host computer can send this command to set the acceleration and deceleration in the position debugging mode.

(6) Set the 32-bit position reference command. The 32-bit data corresponds to the number of pulses. For example, when the numerator value and denominator value are both set to 1 in the electronic gear, and the encoder lines is 2500, the number of pulses required per one revolution of the motor is 10000.

When the position reference is written as 10000, the drive starts at the mechanical zero point and the motor rotates once. When 100000 is written, the motor rotates 10 revolutions. If 0 is written again, the motor rotates to the position just when starting.

(7) Regarding the position mode, whether the transmission position command is an absolute position or a relative position. When the send command is 0X52 0X00 0X00 0X52, the send position is the absolute position. When the send command is 0X52 0X00 0X01 0X53, the position is the relative position.

(8) In position mode, the maximum stable speed limit of the motor output is determined by VLimit (provided that the acceleration/deceleration in position mode has been set to a maximum value of 255). The send command is (0x1d set value up 8 bits set value low 8 bit checksum) where the set value corresponds to the limit speed = (requires set limit speed / 6000) * 16384 , the obtained data is rounded off. For example, if the motor requires 3000 RPM, the set value is 8192. If 1RPM is required, the set value is 3 (rounded).

(9) About the problem of finding the origin of the mechanical Z signal, after the parameter configuration is completed, after sending the origin operation (0x53 0x00 0x00 0x53). And after sending the motor start (0x00 0x00 0x01 0x01), the motor will rotate slowly until the Z signal origin is found, and then it will not move.

(10) About monitoring commands. Send the monitoring command is (0x80 0x00 0x80), after receiving the command, the drive returns the following data: fault information, busbar voltage, output current (which has been amplified by 100 times, the actual display current needs to be divided by 100. For example, the received value is 123. It means the current is 1.23A), output speed (output speed is digital, the conversion relationship is: actual speed = (digital speed / 16384) * 6000), the current position given value up 16 bit, the current position given value low 16 bits, the current position feedback value up 16 bits, and the current position feedback value low 16 bits. Please refer to the above table for the corresponding relationship. The format returned is four data per frame.

The format is: Address Data up 8 bits Data low 8 bits Checksum (takes the low 8 bits).

VI. The use of the host computer debugging software

The drive provides easy-to-use debugging software, all parameters can be written to the inside of the drive through the debug software, while monitoring the status of the drive. The following details will show the use of the software.

6.1 Serial Port Operation

After opening the software, there is a serial port setting in the file drop-down list. Select the serial port number of the PC, and the other ones are as default like the picture below. After setting, apply the settings and open the serial port. The first time the software is opened, the parameters of the drive are read out by default. If the user needs to load the parameters that have been stored and modified, the stored parameter file can be opened from the software.

Figure 6-1

6.2 Basic parameter settings

Pulse direction reference selection (this option is only valid when the position mode external pulse input):

When forward rotation is selected, the input signal is:

pulse + direction (high level), at this time the drive is rotating forward.

pulse + direction (low level), at this time the the drive is rotating reversed.

When reverse is selected, the input signal is:

pulse + direction (low level), at this time the drive is rotating forward.

pulse + direction (high level), at this time the drive is rotating reversed.

Overload factor: The setting parameter range is 0~300%, the default is 200%. This setting is the maximum current allowed to output of the drive. If exceeded the set overload time, it will stop and alarm.

Analog dead zone: The approved range of mechanical zero, zero speed, and zero torque when using analog control. For example, when set to 50, when the digital quantity sampled by AD is less than 50, the drive forced sample value will be 0.

Electronic gear: actual position command = input pulse command * (numerator of the electronic gear ratio / denominator of the electronic gear ratio).

The specific settings are shown in Figure 6-2-1, 6-2-2.

Figure 6-2-1

Figure 6-2-2

6.3 Drive PI Parameter Settings

The parameters that the drive is now open are position loop PDF, speed loop PID. There is a great relationship between parameter adjustment and response. The actual working environment is subject to adjustment.

Under the default parameter setting, if the motor vibrates, reduce the value of the speed loop KpV and increase the value of the speed loop KI appropriately after vibrating situation. If the speed loop KpV is reduced, however the motor is still vibrated, and then reduce the KpP value of the position loop.

In the case of none vibration, slowly increase the KpV value of the speed loop while reducing the KiV value of the speed loop. Under the condition of rigid demand, appropriately increasing the value of the speed loop KdV can reduce the vibration of the motor, and increasing the excessive KdV will cause high-frequency noise, please pay attention, If the above cannot reduce the vibration, properly reduce the KpI value of the current loop. The PI parameter of the current loop is now encrypted. For modification, please contact the factory.

Figure 6-3

Figure 6-4 / Figure 6-5

6.4 Mode Selection and PC Reference

The drive provides 7 control source options, users can select different control methods according to different needs. In the corresponding mode of PC digital input, the text area of the three modes is valid, but the acceleration and deceleration settings are valid only in the PC input mode.

6.5 Status Monitoring
The host computer software provides real-time monitoring of the bus voltage, output current, motor speed, position reference, and position feedback information. The specific status monitoring is shown in Figure 6-5.

6.6 Simple Oscilloscope
The debugging software provides periodic monitoring of U-phase digital current, V-phase digital current, current reference, current feedback, speed reference, speed feedback, position reference, and position feedback signal. At the same time, the current sample waveform or the load history waveform can be recorded

Figure 6-6

Figure 6-7 Password: 8888

6.7 Setting of motor parameters
The motor parameters are fixed when the drive leaves the factory with the motor, and the user can not change them at will, otherwise the drive and equipment will be damaged.
Note: if you want to replace the motor, please confirm the parameters with the motor provider and drive manufacturer and write the relevant setting again .Motor related parameters are non-modifiable parameters after the drive is energized. After modification, it will be valid only after re-energized or the drive system reset.
Number of encoder lines: the resolution of the encoder corresponding to the motor nameplate;
Angle offset: the Angle offset value of the encoder Z signal corresponding to the motor U opposite to the electromotive force negative over zero;
Number of pole pairs: motor pole pairs.

VII. Typical wiring of control signals

Figure 7-1 Wiring diagram of differential mode control signal interface

Figure 7-2 Single-ended mode control signal interface wiring diagram

Special reminder: When the control signal is 12V or 24V, an external current limiting resistor is required. 12V is connected to 1K resistor and 24V is connected to 2K resistor. Otherwise, long-term operation will damage the drive’s opto-isolated device.

BLSD-H Series Brushless DC Motor Drive

admin — Wed, 19 Feb 2020 16:34:22 +0000

Brief Introduction:

Surface mounted technology to improve the reliability of the circuit.
PLC interface, amazing 200A super high current with low voltage and incredible small dimension.
We present industrial chips to meet industrial application temperature requirements.
Optoelectronic isolation for analog voltage / PWM pulse / pulse frequency signal and other security interfaces.
Super reliable design with safe foreward and reverse, safe start, anti-interference, over temperature / over current / short circuit / under voltage / over voltage and other protections.

Definition of Part number:

BLSD	24	35	WDC	2Q	H	F	P	T
BLDC drive	Rated Voltage	Peak current limit	DC input ①	Control mode	Parameter ②	PG type ③	Speed regulation type ④	Temp ⑤

① : This code shows the DC Power input type of the drive: WDC = Wide range DC input; LDC = Ultra low voltage DC input; DC = Normal DC input; AC = AC input; ADC = AC and DC dual purpose.
② : This code shows the parameter type of the drive: H = High current; N = Variable parameter; S = Simple fixed parameter; SH = Small type high voltage; HV = High voltage.
③ : This code shows the PG type: F = PG 1x hall sensor signal/phase, None= 6 x hall sensor signal/phase.
④ : This code shows the speed regulation type: P = 0-3KHz speed regulation, None = voltage command.
⑤ : This code shows the temperature range of the drive: T = -40 ~ +65 ℃ , None = -10 ~ +45℃ .
Note: In order to let the part number easier to read, Some part number code will not be shown in the specification table, a code “X” will be instead. The full part number will be provided in the quotation or the proforma invoice…

Specifications:

Model	Temperature range (ºC)	Voltage range (VDC)	I-pk (A)	I-con (A)	60º/120º Hall sensor	PWM f(kHz)	PI Close loop of speed	SV Ramp time (S)	SV Range (V)	LV /OV	Alm	PG	PI Close loop of current	Para-meter Settings By Switch And Pot	SC /OT	Safe F/R	Safe Start	Heat Sink
BLSD2435DC-2Q-H-X	-10～+45 -40～+65	17～32	17.5～35	8.75～17.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD2450DC-2Q-H-X	-10～+45 -40～+65	17～32	25～50	12.5～25	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD2475DC-2Q-H-X	-10～+45 -40～+65	17～32	37.5～75	18.75～37.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD24100DC-2Q-H-X	-10～+45 -40～+65	17～32	50～100	25～50	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD24150DC-2Q-H-X	-10～+45 -40～+65	17～32	150	75	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD24200DC-2Q-H-X	-10～+45 -40～+65	17～32	200	100	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD3635DC-2Q-H-X	-10～+45 -40～+65	27～45	17.5～35	8.75～17.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD3650DC-2Q-H-X	-10～+45 -40～+65	27～45	25～50	12.5～25	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD3675DC-2Q-H-X	-10～+45 -40～+65	27～45	37.5～75	18.75～37.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD36100DC-2Q-H-X	-10～+45 -40～+65	27～45	50～100	25～50	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD36150DC-2Q-H-X	-10～+45 -40～+65	27～45	150	75	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD36200DC-2Q-H-X	-10～+45 -40～+65	27～45	200	100	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4835DC-2Q-H-X	-10～+45 -40～+65	37～56	17.5～35	8.75～17.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4850DC-2Q-H-X	-10～+45 -40～+65	37～56	25～50	12.5～25	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4875DC-2Q-H-X	-10～+45 -40～+65	37～56	37.5～75	18.75～37.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48100DC-2Q-H-X	-10～+45 -40～+65	37～56	50～100	25～50	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48150DC-2Q-H-X	-10～+45 -40～+65	37～56	150	75	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48200DC-2Q-H-X	-10～+45 -40～+65	37～56	200	100	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD1235LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	17.5～35	8.75～17.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD1250LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	25～50	12.5～25	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD1275LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	37.5～75	18.75～37.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD12100LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	50～100	25～50	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD12150LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	150	75	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD12200LDC-2Q-H-X (Ultra Low Voltage)	-10～+45 -40～+65	5～18	200	100	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4835WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	17.5～35	8.75～17.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4850WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	25～50	12.5～25	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD4875WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	37.5～75	18.75～37.5	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48100WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	50～100	25～50	√	15	√	0.1～10	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48150WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	150	75	√	15	√	0～5	0～5	√	√	24p@8-pole	√	√	√	√	√	√
BLSD48200WDC-2Q-H-X (Ultra Wide Voltage Range)	-10～+45 -40～+65	17～56	200	100	√	15	√	0～5	0～5	√	√	24p@8-pole	√	√	√	√	√	√

Technical Note:

1.Control signals:
F/R—–H or Open=Forward, L or Close=Reverse
EN——H or Open=Disable, L or Close=Enable
BK——H or Open=Running, L or Close=Brake
SV——0~5V speed reference(112K input resistance)
PG—–Speed pulse output(OC)
ALM—Alarm output(OC)

2. Signal wire:
Control signal cable and hall sensors cable can not be tied together with windings cable, otherwise, it will take interference. The long wire should be shielded wire.

3. Alarm conditions:
a. Hall sensor signals are not correct.
b. LV or OV for 1~3S.
c. Short circuit and Over temperature of case (80℃)..
d. Over load for 5~6s continuously.
e. It can be reset by Turn-Off-On DC Power or Disable the driver once.

4. LED indicator:
SC——–Bright=Short circuit , Dark=driver is OK
P/A——-Bright=Driver is OK, Blink=Driver is in alarm
SHAFT—-Bright=Motor shaft is moving, Dark=Motor shaft is in static

5. Braking operation:
The motor speed must be less than the safe brake speed Ns when you brake the motor.
For Y windings, Ns=√3 x Ip x RL x N/ (2x Vp)
For △windings, Ns=IP x RL x N/ (2 x √3 x Vp)
Ip=Peak current(A), RL=Line to line resistance of windings(Ohm)
N=No-load speed(rpm), Vp=Rated voltage(V), Ns=Safe brake speed(rpm)

6. Safe F/R:
If you change F/R of the driver rapidly, it will stop the power stage and motor will be free until the speed is detected as zero,and then to drive in correct direction. This means smooth reverse.

7. Safe start:
If the motor speed is not detected as zero at power on, the driver will be free until the motor speed is zero.

8. Drive setup by pot and switch:
R-SV pot=SV voltage ratio, R-LG pot=Loop gain, R-PC=Peak current ratio, R-RT pot=Ramp time
SW1=60/120 Hall sensors, SW2=Open/Close loop, SW3,4=Speed/Current loop, SW5=Loop filter time, SW6=SV ramp time setting, SW7,8,9,10=Speed range setting.

9. Peak current selection:
Ip>=2xIr or Ip>=4xPo/Vp, Ip is peak current of driver(A), Ir is rated current of motor(A)
Po is rated output power of motor(W), Vp is rated voltage of driver(V)

Customization:


Heat sink	Motor tuning	Logo / brandmark

Heat Sink: Heat sink can be added according to customer request.
Motor Tuning: Drivers can be tuned to fit the motors with different poles to match customer’s applications.
Logo and brandmark: Customer’s Logo/brandmark can be printed on the frame of the driver according to the customer’s request.

BLSD-N Series Brushless DC Motor Drive

admin — Wed, 19 Feb 2020 15:51:32 +0000

Brief Introduction:

Competitive and economical price with adjustable parameters.
Surface mounted technology to improve the reliability of the circuit.
We present industrial chips to meet industrial application temperature requirements.
Optoelectronic isolation for analog voltage / PWM pulse / pulse frequency signal and other security interfaces.
Super reliable design with safe forward and reverse, safe start, anti-interference, over temperature / over current/short circuit / under voltage / over voltage and other protections.

Definition of Part number:

BLSD	24	10	DC	2Q	N	T	F	A	P
BLDC drive	Rated Voltage	Peak current limit	DC input ①	Control mode	Parameter ②	Temp ③	PG type ④	Sensor type ⑤	Speed regulation type ⑥

① : This code shows the DC Power input type of the drive: DC = Normal DC input; LDC = Ultra low voltage DC input; WDC = Wide range DC input; AC = AC input; ADC = AC and DC dual purpose.
② : This code shows the parameter type of the drive: N = Variable parameter; S = Simple fixed parameter; H = High current; SH = Small type high voltage; HV = High voltage.
③ : This code shows the temperature range of the drive: T = -40 ~ +65 ℃ , None = -10 ~ +45℃ .
④: This code shows the PG type: F = PG 1x hall sensor signal/phase, None= 6 x hall sensor signal/phase.
⑤ : This code shows the hall sensor degree of the drive: A = 60° Hall sensor, None = 120° Hall sensor.
⑥ : This code shows the speed regulation type: P = 0-3KHz speed regulation, None = voltage command.
Note: In order to let the part number easier to read, Some part number code will not be shown in the specification table, a code “X” will be instead. The full part number will be provided in the quotation or the proforma invoice…

Specifications:

Model	Temp range (ºC)	Voltage range (VDC)	I-pk (A)	I-con (A)	60º/120º Hall sensor	PWM f(kHz)	PI Close loop of speed	SV Ramp time (S)	SV Range (V)	LV /OV	Alm	PG	Heat Sink	Parameter Settings By Switch And Pot
BLSD1210DC-2Q-N-X	-10～+45 -40～+65	9～16	2.5～10	1.25～5	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD1220DC-2Q-N-X	-10～+45 -40～+65	9～16	5～20	2.5～10	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD1230DC-2Q-N-X	-10～+45 -40～+65	9～16	7.5～30	3.75～15	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD2410DC-2Q-N-X	-10～+45 -40～+65	17～32	2.5～10	1.25～5	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD2420DC-2Q-N-X	-10～+45 -40～+65	17～32	5～20	2.5～10	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD2430DC-2Q-N-X	-10～+45 -40～+65	17～32	7.5～30	3.75～15	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD3610DC-2Q-N-X	-10～+45 -40～+65	27～45	2.5～10	1.25～5	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD3620DC-2Q-N-X	-10～+45 -40～+65	27～45	5～20	2.5～10	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD3630DC-2Q-N-X	-10～+45 -40～+65	27～45	7.5～30	3.75～15	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD4810DC-2Q-N-X	-10～+45 -40～+65	37～55	2.5～10	1.25～5	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD4820DC-2Q-N-X	-10～+45 -40～+65	37～55	5～20	2.5～10	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√
BLSD4830DC-2Q-N-X	-10～+45 -40～+65	37～55	7.5～30	3.75～15	√	15	√	0.1/0.25 /0.5/1.0	0～5	√	√	24p@ 8-pole	X	√

Technical Note:

2. Signal wire:
Control Signal cable and hall sensors cable can not be tied together with windings cable, otherwise, it will take interference. The long wire should be shielded wire.

3. Alarm conditions:
a. Hall sensor signals are not correct.
b. LV or OV for 1~3S.
c. Over temperature of case (80℃).
d. Over load for 5~6s continuously.
e. It can be reset by Turn-Off-On DC Power or Disable the driver once.

4. LED indicator:
P/A——-Bright=Driver is OK, Blink=Driver is in alarm
SHAFT—-Bright=Motor shaft is moving, Dark=Motor shaft is in static

5. Braking operation:
The motor speed must be less than the safe brake speed Ns when you brake the motor.
For Y windings, Ns=√3 x Ip x RL x N/ (2 x Vp)
For △windings, Ns=IP x RL x N/ (2 x √3 x Vp)
Ip=Peak current(A), RL=Line to line resistance of windings(Ohm)
N=No-load speed(rpm), Vp=Rated voltage(V), Ns=Safe brake speed(rpm)

6. Driver setup by pot and switch:
R-SV pot=SV voltage ratio, R-PC=Peak current ratio, SW1=Open/Close loop, SW2=Loop filter time, SW3=Loop gain, SW4,5,6=Speed range setting, SW7,8=SV ramp time setting

7. Peak current selection:
Ip>=2xIr or Ip>=4xPo/Vp, Ip is peak current of driver(A), Ir is rated current of motor(A), Po is rated output power of motor(W), Vp is rated voltage of driver(V)　

Customization:


Heat sink	Motor tuning	Logo / brandmark

Heat Sink: Heat sink can be added according to customer request.
Motor Tuning: Drivers can be tuned to fit the motors with different poles to match customer’s applications.
Logo and brandmark: Customer’s Logo/brandmark can be printed on the frame of the driver according to the customer’s request.

110ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 20:02:08 +0000

General Specification:

Voltage Range: 24v dc (220v also available)
Power Output Range: 250 to 600 watts
Speed Range: up to 9,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing Type: Closed (ventilated also available)

Definition of Part number:

110	ZYT	200	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Attention please: These models below are our typical types which can show our products' performance. If these models can meet your requirement just enough, that's perfect. Or, if you can't find a model which meets your requirement, that's fine, we can compeletely customize the specifications according to your requirement. Please contact us if you have any requirement.

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Current	No load Speed	Length
Units	V	W	rpm	mNm	A	A	rpm	mm
110ZYT200-12V	12	283	2700	1	34.6	4.9	3270	200
110ZYT200-24V	24	514	3070	1.6	26	2.6	3350	200
110ZYT200-48v	48	553	3300	1.6	14.3	2.5	3300	200

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

100ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:56:07 +0000

General Specification:

Voltage Range: 12 & 24v dc (220v also available)
Power Output Range: 180 to 400 watts
Speed Range: up to 9,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing Type: Closed (ventilated also available)

Definition of Part number:

100	ZYT	145	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Current	No load Speed	Length
Units	V	W	rpm	mNm	A	A	rpm	mm
100ZYT145-12V	12	290	3450	0.8	32.5	5	3920	145
100ZYT145-24V	24	290	3450	0.8	15.6	2.3	3920	145
100ZYT165-12V	12	197	2350	0.8	22	3	2250	165
100ZYT165-24v	24	348	4150	0.8	20.3	3.5	4660	165
100ZYT200-12v	12	188	1500	1.2	24.5	3	1900	200
100ZYT200-24V	24	188	1500	1.2	13	1.5	1900	200

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

90ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:49:57 +0000

General Specification:

Voltage Range: 12 & 24v dc (48v also available)
Power Output Range: 150 to 300 watts
Speed Range: up to 9,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing Type: Closed (ventilated also available)

Definition of Part number:

90	ZYT	155	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Speed	Length
Units	V	W	rpm	mNm	A	rpm	mm
90ZYT155-12V	12	250	4750	400	23	5540	155
90ZYT199-12V	12	150	1200	1200	23	1500	199
90ZYT155-24V	24	250	4750	500	13.8	5100	155
90ZYT199-24V	24	150	1200	1200	11.5	1600	199

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

80ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:45:06 +0000

General Specification:

Voltage Range: 12 & 24v dc (48v also available)
Power Output Range: 50 to 230 watts
Speed Range: up to 9,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing type: Closed (ventilated also available)

Definition of Part number:

80	ZYT	122	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Speed	Length
Units	V	W	rpm	mNm	A	rpm	mm
80ZYT122-12V	12	54	1200	430	7.1	1600	122
80ZYT122-24V	24	54	1200	430	3.5	1600	122
80ZYT122-40V	40	54	1200	430	2	1600	122
80ZYT135-12V	12	106	2900	350	11.5	3200	135
80ZYT135-24V	24	106	2900	350	5.8	3200	135
80ZYT135-40V	40	128	3500	350	4	3750	135
80ZYT175-12V	12	207	3200	620	10	3500	175
80ZYT175-24V	24	201	3100	620	6	3500	175
80ZYT175-40V	40	221	3350	630	4.2	3650	175

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

73ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:36:20 +0000

General Specification:

Voltage Range: 12 & 24v dc (240v also available)
Power Output Range: 90 to 180 watts
Speed Range: up to 9,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing type: Closed (ventilated also available)

Definition of Part number:

73	ZYT	127	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Speed	Length
Units	V	W	rpm	mNm	A	rpm	mm
73ZYT127-12V	12	90	4400	200	11	4900	127
73ZYT145-12V	12	120	3700	300	15	4200	145
73ZYT155-12V	12	135	3200	400	16.5	3600	155
73ZYT165-12V	12	150	3000	500	18	3400	165
73ZYT127-24V	24	100	4700	200	5.5	5200	127
73ZYT145-24V	24	130	3900	300	7.5	4500	145
73ZYT155-24V	24	145	3400	400	8.5	3900	155
73ZYT165-24V	24	170	3200	500	9	3600	165

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

63ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:30:53 +0000

General Specification:

Voltage Range: 12 & 24v dc (240v also available)
Power Output Range: 40 to 100 watts
Speed Range: up to 10,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing Type: Closed (ventilated also available)

Definition of Part number:

63	ZYT	95	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Speed	Length
Units	V	W	rpm	mNm	A	rpm	mm
63ZYT95-12V	12	44.5	3100	137	5.2	3600	95
63ZYT95-24V	24	48.4	3300	140	2.7	3600	95
63ZYT95-40V	40	48.7	3500	133	1.7	3800	95
63ZYT125-12V	12	75.4	3000	240	8.7	3500	125
63ZYT125-24V	24	94.7	3350	270	4.9	3650	125
63ZYT125-40V	40	97.5	3450	270	3	3600	125

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.

54ZYT Series permanent magnet DC motor

admin — Mon, 17 Feb 2020 19:23:58 +0000

General Specification:

Voltage Range: 12 & 60v dc
Power Output Range: 30 to 100 watts
Speed Range: up to 10,000 rpm
Operational Temperature: -20°C to +40°C
Insulation Class: F (Consult us for class B)
Bearing Type: High quality ball bearing
Housing Type: Closed (ventilated also available)

Definition of Part number:

54	ZYT	75	12V	X
Frame size	Brushed dc motor	Motor length	Voltage	External code

Specifications:

Model	Voltage	Rated Power	Rated Speed	Rated Torque	Rated Current	No load Speed	Length
Units	V	W	rpm	mNm	A	rpm	mm
54ZYT75-12V	12	24	3280	71	3.57	4140	75
54ZYT81-12V	12	36	3430	99	4.57	4000	81
54ZYT94-12V	12	45	2880	148	5.63	3380	94
54ZYT103-12V	12	60	3130	183	7.34	3630	103
54ZYT113-12V	12	58	2510	219	7.2	2990	113
54ZYT126-12V	12	76	2830	261	9.31	3320	126
54ZYT145-15.2V	15.2	108	2910	353	9.98	3330	145
54ZYT75-48V	48	25	3340	71	0.89	4150	75
54ZYT81-48V	48	36	3490	98	1.14	4010	81
54ZYT94-48V	48	45	2910	148	1.39	3330	94
54ZYT103-48V	48	62	3220	183	1.83	3630	103
54ZYT113-48V	48	59	2590	219	1.8	3000	113
54ZYT126-48V	48	75	2790	261	2.2	3150	126
54ZYT145-48V	48	105	2840	353	2.99	3160	145

Outline:

Customization:


Shaft	Encoder	Brake	Connector	Pulley	Gearbox

Shaft Extensions: All motors can be supplied with single or double ended shaft, keyway or flat cut can made according to per customer’s request. The length of shaft can made as per customer’s request too.
Encoder option: All motors can be supplied with different revolution encoder according to customer’s request.
Brake option: All motors can be supplied with brake with or without hand release.
Cable harness & intergrated connector: Cable harness with or without connectors or intergrated connectors can be supplied according customer’s request.
Pulley & pinion gear: Pulley or pinion gear is available according to customer’s request.
Gearbox option: Most of our motors can be supplied with gearboxes, such as planetary gearbox, worm wheel gearbox and parallel shaft gearbox.